• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Cat flaps let your cat leave and come back whenever they want without needing to let them in or out. They also help stop your cat from urinating in the house.

It is much easier to put a cat flap on a upvc panel than one made of glass, but you will need some skills and the right tools.

Take a look at the Door

Installing a cat door into a front door could be difficult however, as long as the cat flap is of the correct one and you follow the instructions you can make it less difficult. We will show you how to draw the shape and then use a jigsaw in order to cut the door area. Then, we'll finish the job by affixing the cat flap. This will ensure that the flap stays in place and shields the door from wind and rain damaging the door.

To determine the size of the cat flap you require, measure the width of your pet. This will ensure that the flap is large enough to allow your pet to enter and leave the house without having to open and close the door each time, yet small enough to keep them from moving too far in either direction.

Once you have the measurements you can mark where on the door the template should be positioned, usually this is done with an X. However, some kits come with an illustration that outlines where to drill, if you have one, then attach it to the door and use a pencil to draw around the door. If your door has a sill or moulding at the bottom, make sure that you leave enough space between your cat and these elements.

Use a set square to check that you are cutting correctly and to make sure the hole is in a rectangle shape. When you are satisfied with this, you are able to start removing the rest of the door material. If you have a square that you have cut, make use of it to verify that you are cutting correctly and also to ensure that the hole is in a rectangle. Once you are satisfied with this you can begin to take off the remaining door material.

Draw a Line

The cat flap allows you to let your pet in and outside without worrying about unwanted visitors or unwanted gifts. It also stops draughts and helps keep the temperature of your home stable. However, installing a cat flap in your door can seem like an intimidating task for those who've never done it before, which is why many to hire a professional carpenter or joiner to do the job instead. This is an option but you can do it yourself if your tools are right and the directions are adhered to.

Although this is much simpler with a timber door, it is still feasible in uPVC doors, though you need to be very careful to avoid damaging the doors as this will end your warranty. First, you must examine the door's measurements to ensure that it can accommodate the new cat-flap. If you have an ordinary upvc door panel with cat flap fitted panel, this should be easy. However when your door is made of composite or another kind of door, you may have to be more cautious.

The next step is to determine the belly height of your cat. This is the height from the floor to the underside of the cat's stomach and you'll need to locate a place on the door where this measurement will fall within the range that your pet can comfortably go through. Once you've got the information, you'll be required to mark the space with a spirit level and a pencil so you are sure that the opening will fit your cat.

After you have marked the area, you're now ready to cut the hole. You will need to use an jigsaw. It is important that you be patient to ensure that the cuts are smooth and straight rather than rough and uneven, as this could damage your door. You should also remember to wear safety glasses and a dust mask whenever using the jigsaw, since dust from the saw could be harmful to your health. After you've finished the cutting process, you will have to smooth the edges of the hole using sandpaper, so that your cat flap will fit easily into place.

Cut a hole

The process of fitting a cat flap to an existing door panel or double glazing sealed unit can be quite difficult. If you're not proficient in DIY, it is recommended to hire a professional to complete the work for you. A shoddy job might not only look ugly, but it could also be an enigma for security as well as allowing cold air to enter when the cat is outside and hot air to escape when inside.

The hole's location should be marked on the door using an eraser and a spirit level. This will ensure it is positioned correctly and aligns with the rest of the door. Make sure you have sandpaper to smooth out any rough edges.

After the line is traced, you must cut the hole with the jigsaw. Remember to wear any safety equipment for working with the power tool. If you are worried about the noise of the jigsaw, you can purchase an electric version that is quieter and simpler to use.

It is best to only remove the material required to make the flap. A small amount of material will be required for the thickness of the wall of the flap but cutting off more than this can cause problems and even harm the frame of the door.

If the upvc door features a metal panel or frame, it could interfere with the microchip flap. In this scenario, you will need to make an oversize hole to ensure that the metal does not touch the walls of the flap.

If you are fitting a cat flap into a upvc door or double-glazed window with a metal frame, you'll need to talk to a professional who can provide you with a brand new pane of glass with the hole for the cat flap in it. This will be less expensive than Fitting Cat Flap In Upvc Door Panel a cat flap in an existing pane of glass that was not designed specifically for this purpose.

Install the Flap

Cat flaps allow your pet to leave and come whenever they want, allowing them the freedom to relax inside the house when they want to. However, if you own an uPVC door, it might be difficult to fit an animal flap, especially in the absence of glass panes that could be cut to fit one. If you're able to buy and install a replacement half-glazed uPVC panel, then it's possible to add the cat flap fitting near me flap to the doors. It's not as simple as cutting a hole in the door, however there are some things you'll need to take care of first to ensure that it's safe.

A composite, uPVC, or GRP door panel is usually made up of a thin plastic skin which is bonded to an insulating polystyrene base. The material is fairly fragile and care should be taken when cutting through it to avoid damaging. This kind of door has a template you can use to cut the hole.

After you have marked out the hole in your front door, it's time to put in the cat flap. You can pick from a wide range of options, from simple push-button flaps to microchip activated ones that allow your pet in. Whatever type of cat flaps you choose, it's vital that your cat can use the flap comfortably without getting stuck in bad weather.

It's a good idea opt for circular fittings instead of a square one, as circles can be more securely cut into the door glass. This is because square holes can make the glass more susceptible to cracking if a drill is used on it. This is also a safer choice, as you won't have to drill into the toughened glass which could break and cause harm to your pet or your family members. This is especially important if you have child or elderly person in your home who could be hurt by shards of glass cat flap installation near me.